Materials testing breaks down into five major categories: mechanical testing; testing for thermal properties; testing for electrical properties; testing for resistance to corrosion, radiation, and biological deterioration; and nondestructive testing. Standard test methods have been established by such national and international bodies as the International Organization for Standardization (ISO), with headquarters in Geneva, and the American Society for Testing and Materials (ASTM), Philadelphia.
Click here to get more.
materials testing , measurement of the characteristics and behaviour of such substances as metals, ceramics , or plastics under various conditions. The data thus obtained can be used in specifying the suitability of materials for various applications&#;e.g., building or aircraft construction, machinery, or packaging . A full- or small-scale model of a proposed machine or structure may be tested. Alternatively, investigators may construct mathematical models that utilize known material characteristics and behaviour to predict capabilities of the structure.
Structures and machines, or their components, fail because of fracture or excessive deformation. In attempting to prevent such failure, the designer estimates how much stress (load per unit area) can be anticipated, and specifies materials that can withstand expected stresses. A stress analysis, accomplished either experimentally or by means of a mathematical model, indicates expected areas of high stress in a machine or structure. Mechanical property tests, carried out experimentally, indicate which materials may safely be employed.
Static tension and compression testsWhen subjected to tension (pulling apart), a material elongates and eventually breaks. A simple static tension test determines the breaking point of the material and its elongation, designated as strain (change in length per unit length). If a 100-millimetre steel bar elongates 1 millimetre under a given load, for example, strain is (101&#;100)/100 = 1/100 = 1 percent.
A static tension test requires (1) a test piece, usually cylindrical, or with a middle section of smaller diameter than the ends; (2) a test machine that applies, measures, and records various loads; and (3) an appropriate set of grips to grasp the test piece. In the static tension test, the test machine uniformly stretches a small part (the test section) of the test piece. The length of the test section (called the gauge length) is measured at different loads with a device called an extensometer; these measurements are used to compute strain.
Conventional testing machines are of the constant load, constant load-rate, and constant displacement-rate types. Constant load types employ weights directly both to apply load and to measure it. Constant load-rate test machines employ separate load and measurement units; loads are generally applied by means of a hydraulic ram into which oil is pumped at a constant rate. Constant displacement-rate testing machines are generally driven by gear-screws.
Special 67% offer for students! Finish the semester strong with Britannica.
Learn MoreTest machine grips are designed to transfer load smoothly into the test piece without producing local stress concentrations. The ends of the test piece are often slightly enlarged so that if slight concentrations of stress are present these will be directed to the gauge section, and failures will occur only where measurements are being taken. Clamps, pins, threading, or bonding are employed to hold the test piece. Eccentric (nonuniform) loading causes bending of the sample in addition to tension, which means that stress in the sample will not be uniform. To avoid this, most gripping devices incorporate one or two swivel joints in the linkage that carries the load to the test piece. Air bearings help to correct horizontal misalignment, which can be troublesome with such brittle materials as ceramics.
Cell Instruments supply professional and honest service.
Static compression tests determine a material&#;s response to crushing, or support-type loading (such as in the beams of a house). Testing machines and extensometers for compression tests resemble those used for tension tests. Specimens are generally simpler, however, because gripping is not usually a problem. Furthermore, specimens may have a constant cross-sectional area throughout their full length. The gauge length of a sample in a compression test is its full length. A serious problem in compression testing is the possibility that the sample or load chain may buckle (form bulges or bend) prior to material failure. To prevent this, specimens are kept short and stubby.
Static shear and bending testsInplane shear tests indicate the deformation response of a material to forces applied tangentially. These tests are applied primarily to thin sheet materials, either metals or composites, such as fibreglass reinforced plastic.
A homogeneous material such as untreated steel casting reacts in a different way under stress than does a grained material such as wood or an adhesively bonded joint. These anisotropic materials are said to have preferential planes of weakness; they resist stress better in some planes than in others, and consequently must undergo a different type of shear test.
Shear strength of rivets and other fasteners also can be measured. Though the state of stress of such items is generally quite complicated, a simple shear test, providing only limited information, is adequate for most purposes.
Tensile testing is difficult to perform directly upon certain brittle materials such as glass and ceramics. In such cases, a measure of the tensile strength of the material may be obtained by performing a bend test, in which tensile (stretching) stresses develop on one side of the bent member and corresponding compressive stresses develop on the opposite side. If the material is substantially stronger in compression than tension, failure initiates on the tensile side of the member and, hence, provides the required information on the material tensile strength. Because it is necessary to know the exact magnitude of the tensile stress at failure in order to establish the strength of the material, however, the bending test method is applicable to only a very restricted class of materials and conditions.
The test result is expressed as the Charpy impact energy, which is the difference between the initial and final potential energy of the pendulum. The potential energy is proportional to the height of the pendulum, which is related to the angle of deflection. The Charpy impact energy is usually reported in joules or foot-pounds. The higher the Charpy impact energy, the higher the impact toughness of the metal. The test result can also be plotted as a curve that shows how the impact energy changes with temperature. This curve is called the ductile-to-brittle transition curve, and it reveals the temperature range where the metal transitions from ductile (plastic) to brittle (elastic) behavior.
The company is the world’s best Pendulum Hammer Striking Tester supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.