Traffic lights: for safety and efficiency on our roads

28 Oct.,2024

 

Traffic lights: for safety and efficiency on our roads

A traffic signal system is a critical component of any urban infrastructure. At intersections, pedestrian crossings and other traffic points, traffic is not only regulated but also significantly influenced. At Yunex Traffic, we develop traffic signal systems that actively optimise traffic flow, improve pedestrian and cyclist safety and save energy.

You can find more information on our web, so please take a look.

A revolution in urban mobiliy

Every city needs state of the art traffic signals &#; and this is why

Cities with more conventional and therefore outdated traffic signals face a number of problems today and in the future that significantly impair the efficiency, safety and environmental friendliness of their traffic network.

Inefficient traffic flow

Without dynamic traffic control, traffic management often depends on outdated, rigid timetables. This leads to unnecessary delays and congestion, especially during peak traffic times or unforeseen traffic increases. The lack of ability to respond to real-time data can significantly impede traffic flow and worsen urban mobility. Modern control units, such as our sX control unit, controls our traffic signal systems in such a way that allows us to react to traffic situations.

Environmental impact

Cities without modern traffic light systems have difficulties in effectively reducing their CO2 emissions. Conventional signaling systems often have a high energy consumption. Thanks to our 1-watt technology for traffic light systems, massive energy savings can be made as the signal heads are operated with one watt each.

Lack of road safety

Traditional traffic signal systems do not have the advanced monitoring and analysis capabilities that modern intelligent systems offer. This limits their ability to prioritize cyclists or pedestrians through green waves, reducing the safety of these road users. The latest models from Yunex Traffic have detection built into the housing, reducing the need for additional technology at intersections.

High operating and maintenance costs

Reliance on outdated technology can increase operating and maintenance costs for urban transportation systems. Conventional traffic signal systems require more frequent maintenance andreplacement of parts, leading to higher costs in the long run. New enclosures from Yunex Traffic allow for easier maintenance with doors that open on both sides. Without the energy efficiency of modern LED technology, electrical costs are also significantly higher.

Missed opportunities for modernization and integration

Cities without access to intelligent transport solutions are missing out on the opportunity to modernize and better integrate their transport systems. They cannot reap the benefits of a more connected and coordinated system that not only improves traffic flow but also provides data for further urban planning measures.

Benefits for all road users

These are the implications for citizens and decision-makers

For your citizens:

  1. Higher risk for accidents: Lack of advanced monitoring and response to driving behavior increases the risk of accidents. This leads to personal and financial losses as well as a general feeling of insecurity in urban areas.
  2. Lower quality of life: Congestion and high emission levels contribute to air pollution and noise pollution, which negatively affects the general quality of life. This can contribute to health problems such as respiratory diseases and stress-related complaints.
  3. Loss of time and increased stress: Inefficient traffic flows lead to longer commuting times. This causes daily stress and eats up valuable time that citizens could instead use to spend with their families or for hobbies.

For decision makers:

  1. Political and social responsibility: Mayors and city councilors are under pressure to find effective solutions to transportation problems. Failures in this area can lead to dissatisfaction among voters and jeopardize their support in future elections.
  2. Economic burdens: High operating and maintenance costs for outdated transportation systems can put a strain on city budgets. These funds are then lacking in other important areas such as education, health or social services.
  3. Failure to achieve sustainability: Failure to implement effective measures to reduce CO2 emissions can lead to cities missing their climate targets. This not only results in potential penalties but can also affect eligibility for future investments and environmental funding.

Solve tomorrow&#;s challenges today

For safer and more sustainable urban mobility

In a city controlled by modern signal heads, citizens experience a new dimension of traffic safety and environmental friendliness. Yunex Traffic is a leader in the development of traffic signals that not only efficiently control the flow of traffic, but also actively contribute to the reduction of CO2 emissions.

Vision of a safe and green city through our 1-watt technology

Imagine walking through a city where every intersection works seamlessly and safely. Yunex Traffic&#;s traffic lights, equipped with Yulux2 LED technology, use state-of-the-art LED signals that combine brilliant visibility with minimal energy consumption. These traffic lights consume up to 80% less energy than conventional models, helping to reduce urban energy consumption.

Technology that protects lives

Yunex Traffic signal heads are equipped with a multi-level monitoring system that meets the highest safety standards (SIL3-certified). This system not only guarantees safety at intersections, but also ensures general traffic flow control through its precise operation. The integrated microprocessors continuously evaluate large amounts of data in order to optimize the performance of the LEDs and thus ensure constant and reliable signaling.

A new level of visual clarity

The LED technology in the Yulux2 signal heads almost completely eliminates the dangerous phantom light effect, which can be particularly challenging when the sun is low in the sky. This ensures that the signals are clearly visible in all lighting conditions, which significantly increases safety at junctions. The high phantom class 5, which almost all Yunex traffic signal heads achieve, ensures that every road user can interpret the signals correctly, regardless of the time of day or weather conditions.

Reliability that counts

The durability and reliability of Yunex Traffic signal heads are unparalleled. They are built to withstand harsh urban conditions and offer a long-term, low-maintenance solution for cities. Improved thermal management and robust components ensure that these signal heads will operate reliably for years without the need for frequent maintenance or replacement.

Our Alulight housing in particular can easily create a smaller figure when it comes to cutting the budget.

Efficient urban mobility

With Yunex traffic signal heads, life in the city feels different: safer, cleaner and more efficient. Citizens enjoy an improved quality of life with less noise and cleaner air. Decision-makers in city administration benefit from lower operating costs and the certainty that their investments in infrastructure will have a long-term positive impact.

Yunex Traffic not only stands for modern technology, but also for a more sustainable vision of urban mobility that shows how cities can be transformed by intelligent traffic control solutions.

Revolutionary solutions for modern cities

Innovative signal heads from Yunex Traffic

Ecolight &#; The basis for robust traffic control

The Ecolight housing of our traffic signal systems is the fundamental solution for cities that are focused on sustainability and efficiency. The housing made of high-quality polycarbonate not only guarantees long-lasting robustness and resistance to environmental influences, but also supports environmentally friendly traffic control when our energy-saving LED technology is used in it.

The simple installation and handling of the Ecolight signal heads significantly reduce installation and maintenance costs, which helps local authorities to use their budgets more efficiently.

Alulight &#; Modern design meets maximum efficiency

The Alulight housing represents the pinnacle of sleek and modern design at Yunex Traffic. These traffic lights can combine the efficient Yulux2 LED technology with an elegant, flat aluminum housing specially designed for its durability and stability. The Alulight model is particularly suitable for urban environments that want to meet high aesthetic standards.

The powder coating makes the housing extremely resistant to corrosion and chemical influences, which extends the service life and reduces the need for frequent maintenance. This traffic light system is not only an eye-catcher, but also an example of how state-of-the-art technology can help reduce traffic emissions by making traffic flow more efficient.

Mini &#; Compact safety for all road users

The mini signal head model from Yunex Traffic has been specially developed to meet the needs of cyclists and pedestrians. These compact traffic signal heads offer exceptional performance and reliability despite their small size. With a modern design and robust construction, the mini traffic lights provide safe and efficient traffic management, especially in urban areas with high levels of cyclist and pedestrian traffic.

They are easy to install and require minimal maintenance, making them a cost-effective solution for improving urban mobility.

Download our Signal Head Brochure now to discover our innovative solutions.

Future-oriented competitive advantage

Our Traffic Signals &#; Your Advantages

The innovative traffic light systems from Yunex Traffic offer cities decisive advantages that go far beyond mere traffic control. By implementing 1-watt technology, Yunex Traffic not only enables a significant reduction in energy consumption of up to 80%, but also a considerable reduction in CO2 emissions. This contributes significantly to achieving urban climate targets and supports the development towards a more sustainable urbanity.

Energy efficiency and cost savings

The use of Yulux2 VLP technology in our various housings drastically reduces energy costs. The innovative 1-watt technology reduces the energy consumption of the traffic light systems by up to 80% compared to traditional systems. This leads to long-term cost savings and a rapid amortization of investment costs, making this technology an economically attractive solution for municipalities.

Improved traffic safety and flow

Yunex Traffic&#;s intelligent traffic control system uses the latest measurements and analyses to react dynamically to changes in traffic volumes. This optimizes traffic flow, minimizes congestion and reduces waiting times. The green time extensions specially integrated for cyclists also increase the safety and attractiveness of cycling in urban areas.

Sustainability and environmental protection

In addition to energy efficiency, the traffic light systems from Yunex Traffic actively contribute to environmental protection. The reduction in fuel consumption through optimized traffic flow leads to a further reduction in urban CO2 emissions. This not only supports the environmental goals of local authorities, but also improves the quality of life of the urban population through cleaner air and less noise.

Reliability and maintenance efficiency

The robust design of Yunex traffic signal heads ensures a long service life and minimal maintenance requirements. This reduces operational interruptions and ensures continuous and reliable operation of the traffic infrastructure. The systems&#; low susceptibility to faults also increases safety at critical traffic junctions.

Flexibility and future-proofing

Yunex Traffic&#;s signal heads are designed to be easily integrated into existing traffic networks, providing a flexible and future-proof solution to urban traffic problems. Combining the latest LED technology with digital control, these traffic signal systems are ideally equipped to meet the demands of a dynamic and rapidly evolving urban environment.

Our 1 Watt technology significantly reduces the energy consumption of the traffic lights in your city.

We think a step ahead

Additional features of our traffic signals

Yunex Traffic&#;s innovative traffic signal systems are equipped with a variety of advanced features that sustainably transform and improve urban mobility. These features offer significant benefits in terms of safety, efficiency and environmental protection, making them an essential choice for modern traffic management solutions.

  • Dimmable versions: The dimmable LED inserts from Yunex Traffic offer adaptive light control, which makes it possible to reduce the intensity of the light signals at night. This minimizes glare for drivers and at the same time improves the energy efficiency of the systems. By reducing the light intensity, visibility is optimized in different ambient light conditions without compromising safety. The dimming technology adjusts automatically to ensure the best visibility and safety at all times.
  • Simple replacement of the symbol masks: The flexibility of the system is further enhanced by the easy interchangeability of the symbol masks. These masks can be changed quickly and without tools, which simplifies maintenance and allows the signal heads to be quickly adapted to changing traffic situations. Whether temporary traffic routing or long-term changes in traffic flow, Yunex Traffic enables a rapid response.
  • PLUS technology: The innovative PLUS technology from Yunex Traffic revolutionizes the installation and maintenance of traffic signal systems. Decentralized switching of the LED circuits directly in the signal head significantly reduces cabling costs and commissioning times. This technology makes installation more efficient and cost-effective, especially for cities that want to modernize their existing infrastructure.
  • High reliability and durability: Yulux2 technology relies on high-quality materials and sustainable technology to guarantee maximum service life and reliability. Improved thermal management ensures that the components function optimally even under difficult conditions. The longevity of the signaling devices reduces the need for frequent maintenance and lowers operating costs in the long term.
  • Electronic monitoring: Another key feature is the electronic monitoring of each LED light source. This system ensures that the performance of the LEDs always remains within the optimum range. Irregularities are detected immediately and lead to the affected signal being switched off automatically, which significantly increases safety on the road.
  • Simple retrofitting and compatibility: Yunex Traffic also offers retrofit kits that allow existing systems to be quickly and easily upgraded to the latest technology. This compatibility ensures that even smaller cities and municipalities can benefit from advanced traffic technology without having to install completely new systems.

Upgrade our city&#;s infrastructure with innovative traffic lights

Revolutionize your urban mobility with Yunex Traffic

Modern traffic lights for efficient, safe and environmentally friendly traffic management

In today&#;s urban context, high-quality traffic signal systems play a crucial role in the design of sustainable and efficient traffic systems. With the introduction of smart technologies, Yunex Traffic offers a range of cutting-edge solutions aimed at optimizing traffic flows and revolutionizing urban mobility.

Traffic Controllers

Intelligent traffic control with Yutraffic sX

Yunex Traffic takes traffic control to a new level with the Yutraffic sX control unit. This advanced control unit enables flexible and dynamic adaptation of traffic signal systems to the current traffic volume.

Through the use of hot standby processors and over-the-air updates, Yutraffic sX ensures continuous functionality and offers the possibility to update safely even during operation. This contributes to increased traffic efficiency and reduced emissions while improving road safety.

Yulux2-Technology

Use of modern signaling devices

The LED-based inserts of the signal heads from Yunex Traffic are not only energy-efficient, but also extremely reliable and durable. With features such as dimmable lighting at night, they help to reduce light pollution and energy consumption.

The simple replacement of the symbol masks and the integration of PLUS technology, which enables decentralized switching of the LED circuits, considerably simplify the installation and maintenance of the signal heads.

Traffic Detectors

Intelligent traffic detectors for
precise data

To support these advanced systems, Yunex Traffic uses intelligent traffic detectors that provide precise information about the current traffic situation. These detectors can recognize a wide variety of road users and record relevant data such as speed and vehicle type, enabling even finer adjustment of the traffic light systems.

Specialized sensors for cyclists and pedestrians also promote safety and efficiency in urban traffic networks. We now also supply signal head housings that already include our detection.

Smart Mobility & Smart City

Advantages for cities and road
users

By integrating these technologies, cities can significantly improve their traffic systems. Less congestion, reduced environmental impact, increased safety and improved traffic flows are just some of the benefits that can be realized through the use of Yunex Traffic light signal systems.

Traffic signals & signal heads: FAQ

What special functions do intelligent traffic signals offer for urban traffic networks?

Intelligent traffic signal systems use various sensors and control systems to maximize efficiency at intersections. These systems can adjust traffic flow on demand to ensure optimal permeability. Intelligent traffic signal systems also offer green request operation capabilities, where road users can actively request green phases, reducing waiting times and improving road user satisfaction.

How is a traffic signals installed and commissioned?

The commissioning of a traffic signal system requires careful planning and coordination with the local traffic conditions. Installation typically involves setting signal head poles, laying cables and setting up the control software for the controller. Modern traffic signal systems can also include features such as pilot-controlled adaptive traffic control, which enables dynamic adjustment of signal timing to optimize traffic flow based on real-time data.

What are the advantages of LED traffic lights?

The use of LED technology in traffic signal systems offers numerous advantages, including a longer service life and lower energy costs compared to conventional light bulbs. LED traffic signal systems are also more robust and less prone to failure, which reduces maintenance costs and simplifies commissioning. The LED units can also be used safely in steel battery containers due to their low heat generation, without the risk of overheating.

How does a traffic lights improve safety at intersections?

Traffic light systems improve safety at intersections by regulating the flow of traffic and minimizing conflicts between different road users. Modern LED traffic light systems offer increased visibility, which is particularly important at night or in bottlenecks. These traffic light systems are often controlled using advanced frequencies that enable a rapid response to traffic changes, which is particularly advantageous at complex intersections.

What is the cost of a traffic light?

The cost of a traffic signal system can vary greatly depending on the complexity and technology of the system. Standard LSAs can be cheaper, while more advanced systems with LED technology and integrated radar sensors are more expensive to purchase, but save costs during operation. Delivery time and the cost of installation and maintenance can also affect the overall cost.

What are the differences between the traffic signals?

There are different types of traffic signal systems (traffic lights), including standard traffic lights for pedestrians and vehicles as well as more complex systems such as those with LED technology that adopt the LED traffic light standard. Some traffic signal systems are specifically designed for intersections with high traffic volumes, while others are used in narrow areas or less frequented side streets. Innovative traffic signal systems can also be equipped with radar sensors and LED technology for more dynamic traffic control.

Traffic light

Signaling device to control competing flows of traffic

This article is about lights used for signalling. For other uses, see Traffic light (disambiguation)

"Stoplight" redirects here. For other uses, see Stoplight (disambiguation)

An LED 50-watt traffic light in Portsmouth, United Kingdom

Traffic lights, traffic signals, or stoplights &#; also known as robots in South Africa[1][2], Zambia, and Namibia &#; are signaling devices positioned at road intersections, pedestrian crossings, and other locations in order to control the flow of traffic.[3]

Traffic lights normally consist of three signals, transmitting meaningful information to road users through colours and symbols, including arrows and bicycles. The regular traffic light colours are red, yellow (also known as amber), and green arranged vertically or horizontally in that order. Although this is internationally standardised,[4] variations in traffic light sequences and laws exist on national and local scales.[5]

Traffic lights were first introduced in December on Parliament Square in London to reduce the need for police officers to control traffic.[6] Since then, electricity and computerised control has advanced traffic light technology and increased intersection capacity. The system is also used for other purposes, including the control of pedestrian movements, variable lane control (such as tidal flow systems or smart motorways), and railway level crossings.

History

[

edit

]

The first system of traffic signals, which was a semaphore traffic signal, was installed as a way to replace police officer control of vehicular traffic outside the Houses of Parliament in London on 9 December . This system exploded on 2 January and was thus taken down. But, this early traffic signal led to other parts of the world implementing similar traffic signal systems. In the first two decades of the 20th century, semaphore traffic signals like the one in London were in use all over the United States. These traffic signals controlled by a traffic officer who would change the commands on this signal to direct traffic.

In , the first electric traffic light was developed by Lester Wire, a policeman in Salt Lake City, Utah.[9] It was installed by the American Traffic Signal Company on the corner of East 105th Street and Euclid Avenue in Cleveland, Ohio.[11][12] The first four-way, three-colour traffic light was created by William Potts in Detroit, Michigan in .[13] His design was the first to include an amber 'caution' light along with red and green lights.[14] Potts was Superintendent of Signals for the Police Department of Detroit. He installed automatic four-way, three-colour traffic lights in 15 towers across Detroit in .[15][14][13] By , traffic towers were beginning to be controlled by automatic timers more widely. The main advantage of the use of the timer was that it saved cities money by replacing traffic officers. The city of New York was able to reassign all but 500 of its 6,000 officers working on the traffic squad, saving the city $12,500,000.

In , Garrett Morgan patented a design of a manually operated three-way traffic light with moving arms.[17]

The control of traffic lights made a big turn with the rise of computers in America in the s. One of the best historical examples of computerized control of lights was in Denver in . In , the city of Toronto was the first to use more advanced computers that were better at vehicle detection. The computers maintained control over 159 signals in the cities through lines.

Vehicular signals

[

edit

]

Traffic lights can have several additional lights for filter turns or bus lanes.

Road crossing of A970 with Sumburgh Airport's runway in Shetland. The movable barrier closes when aircraft land or take off. Horizontally-mounted signals in Japan

A set of lights, known as a signal head,[19]:&#;3.2.4&#; may have one, two, three, or more aspects. The most common signal type has three aspects facing the oncoming traffic: red on top, amber (yellow) below, and green below that. Additional aspects may be fitted to the signal, usually to indicate specific restrictions or filter movements.

Meanings of signals

[

edit

]

The Vienna Convention on Road Signs and Signals Chapter III provides international standards for the setup of traffic signal operations. Not all states have ratified the convention. A three-colour signal head should have three non-flashing lights which are red, amber, and green, either arranged horizontally (on the side opposite to the direction of traffic) or vertically (with red on top). A two-colour signal head may be used in temporary operation and consists of red and green non-flashing lights. In both cases, all lights should be circular or arrow-shaped.[4] Permissible signals for regulating vehicle traffic (other than public transport vehicles) are outlined in Article 23:[4]

Standard meanings for traffic lights internationally (Vienna Convention, Article 23) Light type Meaning Non-flashing Red Traffic may not proceed beyond the stop line, or otherwise enter the intersection Red/Amber The signal is about to change, but the red light rules do apply Amber Traffic may not pass the stop line or enter the intersection, unless it cannot safely stop when the light shows Green Traffic may proceed, unless it would not clear the intersection before the next change of phase Flashing Red Traffic must not pass the stop line at a level crossing, approach to swing bridge or ferry landing stages, emergency vehicles entering the road, or on the approach to low-flying aircraft. In addition, to attract attention in these locations, it is also equipped with additional alarms and voice prompts Amber Traffic may proceed with caution

Green arrows are added to signals to indicate that drivers can travel in a particular direction, while the main lights for that approach are red, or that drivers can only travel in one particular direction. Alternatively, when combined with another green signal, they may indicate that turning traffic has priority over oncoming traffic (known as a "filter arrow").[19]:&#;3.5&#; Flashing amber arrows typically indicate that road users must give way (to other drivers and pedestrians) before making a movement in the direction of the arrow. These are used because they are safer, cause less delay, and are more flexible. Flashing amber arrows will normally be located below the solid amber.[20]

Green arrows

[

edit

]

Arrow aspects may be used to permit certain movements or convey other messages to road users. A green arrow may display to require drivers to turn in a particular direction only or to allow drivers to continue in a particular direction when the signal is red.[19]:&#;3.5&#; Generally, a green phase is illuminated at the beginning of the green phase (a "leading turn") or at the end of the green phase (a "lagging turn").[citation needed] An 'indicative arrow' may be displayed alongside a green light. This indicates to drivers that oncoming traffic is stopped, such that they do not need to give way to that traffic when turning across it. As right-turning traffic (left-side drive) or left-turning traffic (right-side drive) does not normally have priority, this arrow is used to allow turning traffic to clear before the next phase begins.[19]:&#;3.5&#;

Some variations exist on this set up. One version is a horizontal bar with five lights &#; the green and amber arrows are located between the standard green and amber lights. A vertical five-light bar holds the arrows underneath the standard green light (in this arrangement, the amber arrow is sometimes omitted, leaving only the green arrow below the steady green light, or possibly an LED-based device capable of showing both green and amber arrows within a single lamp housing).[citation needed] Some newer LED turn arrows seen in parts of Canada are capable of multicoloured animation. Such lights will often display a flashing and animated green or amber arrow when the dedicated turn is allowed but then transform into a red arrow on a white background with a red line through it, emphasising that the turn is no longer allowed. These lights will also often have the words "no turn" displayed, or an explanatory reason why the turn is not allowed, such as "train" in the case of a rail or light rail crossing. [citation needed]

A third type is known as a "doghouse" or "cluster head" &#; a vertical column with the two normal lights is on the right side of the signal, a vertical column with the two arrows is located on the left, and the normal red signal is in the middle above the two columns. Cluster signals in Australia and New Zealand use six signals, the sixth being a red arrow that can operate separately from the standard red light.[citation needed] In a fourth type, sometimes seen at intersections in Ontario and Quebec, Canada, there is no dedicated left-turn lamp per se. Instead, the normal green lamp flashes rapidly, indicating permission to go straight as well as make a left turn in front of opposing traffic, which is being held by a steady red lamp. (This "advance green", or flashing green can be somewhat startling and confusing to drivers not familiar with this system. This also can cause confusion amongst visitors to British Columbia, where a flashing green signal denotes a pedestrian-controlled crosswalk. For this reason, Ontario is phasing out the use of flashing green signals and instead replacing them with arrows.)[21][22]

Countdown lights

[

edit

]

Popular in Vietnam and China, countdown lights are additional lights installed next to (or above or below) the main signal lights. The countdown light is displayed by a countdown number with different colors (usually red, yellow, green), matching the color of the light on. When the light counts to "0" (or 1), the main light color immediately changes. Countdown lights may have zeros in the tens or none, some countdown lights may flash when getting ready to zero. Yellow lights can also have countdown lights, but most lights do not. Usually the countdown light has 2 digits, in case the time of the main light (usually the red light, rarely the green light) is longer than 100 seconds, depending on the type of light, the following possibilities may occur:

  1. Lights have not counted down, when 99 seconds are left, start counting. During the standby time, the light may be displayed as "99", "00", "--" or not displayed.
  2. Last 2 digits count light of the timeout (the counter light is 15 while the time is 115 seconds, there are some types of lights that count as "-9" or "9-" when the time is 109 seconds)
  3. Tens digit on the displayer becomes a letter. Displaying A0 for 100 seconds, B0 for 110 seconds, so forth.
  4. Displaying only last 2 digits but with flashing to indicate it's more than 100.
Countdown light

Issue about yellow light dilemma zone in South Korea

[

edit

]

In South Korea, the yellow light dilemma zone is not legally recognized. In other words, when the yellow light is on, traffic may not pass the stop line or enter the intersection even if cannot safely stop when the light shows.

This has been reaffirmed by the ruling of the Supreme Court of Korea in May ,[23][24] for a case where the driver was speeding at 62 km/h in a street limited up to 40 km/h (55 % upper than the allowed speed)[25].

Criticism in South Korea says that this is unrealistic and unreasonable. In addition, this can cause multiple collisions due to sudden braking.

In when speed limit was up to 60 km/h, proposed alternatives to this kind of collision were only roundabouts, speed compliance increase and speed practice reduction or elderly zones are also proposed solutions[26].

Yellow trap

[

edit

]

Without an all-red phase, cross-turning traffic may be caught in a yellow trap. When the signal turns yellow, a turning driver may assume oncoming traffic will stop and a crash may result. For this reason, the US bans sequences that may cause a yellow trap.[27] This can also happen when emergency vehicles or railroads preempt normal signal operation. [28] In the United States, signs reading "Oncoming traffic has extended green" or "Oncoming traffic may have extended green" must be posted at intersections where the "yellow trap" condition exists.[29][30]

Variations

[

edit

]

The United States is not party to the Vienna Convention; rather, the Manual on Uniform Traffic Control Devices (MUTCD) outlines correct operation in that country. In the US, a single signal head may have three, four, or five aspects (though a single aspect green arrow may be displayed to indicate a continuous movement). The signals must be arranged red, amber, and green vertically (top to bottom) or horizontally (left to right).[31] In the US, a single-aspect flashing amber signal can be used to raise attention to a warning sign and a single-aspect flashing red signal can be used to raise attention to a "stop", "do not enter", or "wrong way" sign.[31] Flashing red or amber lights, known as intersection control beacons, are used to reinforce stop signs at intersections.[32] The MUTCD specifies the following vehicular signals:[31]

Standard meanings for traffic lights in the United States (MUTCD, Chapter 4) Signal Meaning (steady) Meaning (flashing)
Circular green Traffic can proceed in any permitted direction, yielding to pedestrians in a crosswalk or other vehicles when turning Not to be used
Green arrow Traffic can proceed in the direction shown by the arrow, yielding to any pedestrians in a crosswalk or other vehicles in the intersection
Circular yellow The green movement is being terminated and a red signal will soon be displayed Traffic can cautiously enter the intersection, yielding to pedestrians and other vehicles
Yellow arrow The green or flashing arrow movement is being terminated Traffic can cautiously enter the intersection to make the movement displayed by the arrow, yielding to pedestrians and other vehicles
Circular red Unless another signal permits, traffic shall not enter the intersection except to lawfully turn on red Traffic must stop before entering the intersection, but may then treat the signal by the same rules as a STOP sign.
Red arrow Traffic shall not make the movement displayed by the arrow Traffic must stop before entering the intersection, but may then treat the signal by the same rules as a stop sign to make the movement displayed by the arrow. A traffic signal in Halifax, Nova Scotia, with specially shaped lights to assist people with colour blindness

In the Canadian province of Quebec and the Maritime provinces, lights are often arranged horizontally, but each aspect is a different shape: red is a square (larger than the normal circle) and usually in pairs at either end of the fixture, amber is a diamond, and green is a circle. In many southern and southwestern U.S. states, most traffic signals are similarly horizontal in order to ease wind resistance during storms and hurricanes.[33] Japanese traffic signals mostly follow the same rule except that the green "go" signals are referred to as &#; (ao), typically translated as "blue", reflecting a historical change in the Japanese language. As a result, Japanese officials decreed in that the "go" light should be changed to the bluest possible shade of green, bringing the name more in line with the color without violating the international "green means go" rule.[34]

In the UK, normal traffic lights follow this sequence:[35]

  • Red &#; Stop, do not proceed
  • Red and Amber &#; Get ready to proceed, but do not proceed yet
  • Green &#; Proceed if the intersection or crossing is clear; vehicles are not allowed to block the intersection or crossing
  • Amber &#; Stop, unless it is unsafe to do so

A speed sign is a special traffic light, variable traffic sign, or variable-message sign giving drivers a recommended speed to approach the next traffic light in its green phase[36] and avoid a stop due to reaching the intersection when lights are red.[37][a]

Pedestrian signals

[

edit

]

Pedestrian signals are used to inform pedestrians when to cross a road. Most pedestrian signal heads will have two lights: a 'walk' light (normally a walking human figure, typically coloured green or white) and a 'don't walk' light (normally either a red or orange man figure or a hand), though other variations exist.[38]

Pedestrian sequences in various countries Country/ies Sequence Notes Australia, New Zealand, Philippines Green man: safe to cross

Flashing red man: do not start to cross; if it appears during crossing, then continue to cross if unable to stop safely

Red man: do not cross

Several intersections in Wellington, New Zealand, have alternative green man figures. Eight intersections near Parliament Buildings have silhouettes of suffragette Kate Sheppard,

[

39

]

while four intersections along Cuba Street have silhouettes of drag performer and LGBT rights activist Carmen Rupe.

[

40

]

China Green: safe to cross

Red: do not cross

Amber (steady, after green, before red): continue to cross only if unable to stop safely

Flashing amber: cross with caution (often used in low-traffic crossing or after midnight)

Japan Blue or green man: safe to cross (cyclists may cross or turn left)

Flashing blue or green man: do not start to cross; if it appears during crossing, then continue to cross if unable to stop safely

Red standing man: do not cross

Germany, Czechia, Central Europe Green: safe to cross

Amber: continue to cross only if unable to stop safely

Flashing amber: cross with caution, obey signage (used when lights are out of order or shut down)

Red: do not cross

Red and amber: do not cross, prepare for green

In Germany, Ampelmännchen pedestrian traffic signals have come to be seen as a nostalgic sign for the former German Democratic Republic.

In Germany, the fine for crossing a red light if caught is as of between &#;5 and &#;10.[41]

United Kingdom, Ireland, Hong Kong, Switzerland, Macao Green walking man: safe to cross

Flashing green man or no man: do not start to cross (only at mid-block crossings); if it appears during crossing, then continue to cross if unable to stop safely

Red standing man: do not cross

In the United Kingdom, there is no direct offence committed if a pedestrian fails to obey crossing signals and many lights commonly only use two still images &#; a green walking person and a red standing man, this being the general case where the crossing is at a road junction and the pedestrian signals are in combination with those controlling vehicular traffic. United States, Canada, Mexico (Tijuana), Philippines (Makati, Davao) Formerly signals used the text:

[

42

]

WALK

DONT WALK

Modern version:

White walking man: cross with caution

Flashing orange stophand: do not start to cross; if it appears during crossing, then continue to cross if unable to stop safely

Orange stophand: do not enter the intersection

The U.S. state of Massachusetts allows an unusual indication variation for pedestrian movement. At signalized intersections without separate pedestrian signal heads, the traffic signals may be programmed to turn red in all directions, followed by a steady display of amber lights simultaneously with the red indications. During this red-plus-amber indication, the intersection is closed to vehicular traffic and pedestrians may cross, usually in whatever direction they choose. Israel Red standing man: do not cross; if it appears during crossing, then continue to cross if unable to stop safely

Green walking man: safe to cross

France green and light, traditionally and in compliance with the international conventions. In , a two year experiment was allowed to start on 8 intersections experimenting blinking yellow light and 7 other one frozen yellow light

[

43

]

. Traffic light animation (pedestrians, cyclists and traffic) in Ljubljana, Slovenia

Where pedestrians need to cross the road between junctions, a signal-controlled crossing may be provided as an alternative to a zebra crossing or uncontrolled crossing. Traffic lights are normally used at crossings where vehicle speeds are high, where either vehicle or pedestrian flows are high or near signalised junctions.[19]:&#;c.18&#; In the UK, this type of crossing is called a pelican crossing, though more modern iterations are puffin and pedex crossings. In the UK, these crossings normally need at least four traffic signals, which are of a regular type (red, amber, and green), two facing in each direction. Furthermore, pedestrians will be provided with push buttons and pedestrian signals, consisting of a red and green man. Farside signals are located across the crossing, while nearside signals are located below the traffic lights, facing in the direction of oncoming traffic.[19]:&#;c.18&#; A HAWK beacon is a special type of traffic used in the US at mid-block crossings. These consist of two red signals above a single amber signal. The beacon is unlit until a pedestrian pushes the cross button. Then an amber light will show, followed by both red lights, at which point the 'Walk' symbol will illuminate for pedestrians. At the end of the crossing phase, the 'Don't Walk' symbol will flash, as will the amber traffic light.[44]

The Shibuya Crossing, in Tokyo, is a famous example of a pedestrian scramble with diagonal crossings.

Pedestrians are usually incorporated into urban signalised junctions in one of four ways: no facilities, parallel walk, walk with traffic, or all-red stages. No facilities may be provided if pedestrian demand is low, in areas where pedestrians are not permitted, or if there is a subway or overpass. No provision of formal facilities means pedestrians will have to self-evaluate when it is safe to cross, which can be intimidating for pedestrians.[19]:&#;71&#; With a "parallel walk" design, pedestrians walk alongside the traffic flow. A leading pedestrian interval may be provided, whereby pedestrians get a "walk" signal before the traffic gets a green light, allowing pedestrians to establish themselves on the crossing before vehicles begin to turn, to encourage drivers to give way.[45] A 'walk with traffic' facility allows pedestrians to go at the same time as other traffic movements with no conflict between movements. This can work well on one-way roads, where turning movements are banned or where the straight-ahead movement runs in a different stage from the turning movement. A splitter island could also be provided. Traffic will pass on either side of the island and pedestrians can cross the road safely between the other flows.[19]:&#;72&#;

An all-red stage, also known as a full pedestrian stage, a pedestrian scramble or a Barnes Dance,[b] holds all vehicular traffic at the junction to allow pedestrians time to safely cross without conflict from vehicles. It allows allows the use of diagonal crossings. This may require a longer cycle time and increase pedestrian wait periods, though the latter can be eased by providing two pedestrian stages.[19]:&#;71&#;72&#;

A diagram of a countdown timer in the US style

Pedestrian countdown timers are becoming common at urban signal-controlled crossings. Where a pedestrian countdown is shown, it is normally used in conjunction with the flashing hand signal (in the US and Canada) or blackout period (UK), showing the amount of time remaining in seconds until the end of the flashing hand or blackout.[19][46] Pedestrian countdown timers do not significantly increase or reduce the number of red- and amber-light running drivers. Studies have found that pedestrian countdown timers do significantly improve pedestrian compliance over traditional pedestrian signals; however, results are mixed.[46][47]

Smartphone Zombie ribbon

[

edit

]

As the 12 to 45% of pedestrian deaths caused by 'pedestrian distraction' has been linked to cell usage,[48] some cities (including Sydney, Seoul, Augsburg, Bodegraven, Aviv, and Singapore) have installed LED strips embedded in the sidewalk before crosswalks to warn distracted pedestrians of immanent pedestrian crossings.[49] This additional signal, which is synchronized with conventional signals, aims to decrease injury rates by telling distracted pedestrians when it is safe to cross the road without them having to lift their head.

Auditory and tactile signals

[

edit

FAMA Product Page

]

In some jurisdictions such as Australia, pedestrian lights are associated with a sound device, for the benefit of blind and visually impaired pedestrians. These make a slow beeping sound when the pedestrian lights are red and a continuous buzzing or fast beeping sound when the lights are green. In the Australian States of Queensland, New South Wales, Victoria, and Western Australia, the sound is produced in the same unit as the push buttons. In a circle above the button, the sound is produced and can be felt along with a raised arrow that points in the direction to walk.[50] This system of assistive technology is also widely used at busy intersections in Canadian cities. In the United Kingdom, the Puffin crossings and their predecessor, the Pelican crossing, will make a fast beeping sound to indicate that it is safe to cross the road. The beeping sound is disabled during the nighttime so as not to disturb any nearby residents.[51]

In some states in the United States, at some busy intersections, buttons will make a beeping sound for blind people. When the light changes, a speaker built into the button will play a recording to notify blind people that it is safe to cross. When the signal flashes red, the recording will start to count down with the countdown timer. In several countries such as New Zealand, technology also allows deaf and blind people to feel when lights have changed to allow safe crossing. A small pad, housed within an indentation in the base of the box housing the button mechanism, moves downwards when the lights change to allow crossing. This is designed to be felt by anyone waiting to cross who has limited ability to detect sight or sound. In Japan, a traffic light emits an electronic sound that mimics the sound of birdsong to help the visually impaired. Some traffic lights fix the order and type of sound so that they can tell which direction is a green light. In general, "Piyo" (peep) and "Piyo-piyo", which is a small bird call, and "Kakkō" and "Ka-kakkō", which is a cuckoo call, are associated with this system.[52] Some pedestrian crossings in Lithuania make a slow beeping sound indicating that the traffic light is about to turn off.

Cycle signals

[

edit

]

Traffic light for a bike lane, NYC An advanced stop line at traffic lights in Liverpool

Where cycle lanes or cycle tracks exist on the approach to a signal-controlled junction, it must be considered how to incorporate cyclists safely into the junction to reduce conflict between motor vehicles and cyclists.

An advanced stop line can be placed after the stop line at traffic lights. This allows cyclists to position themselves in front of traffic at a red light and get a headstart.[53]

In the US, design advice typically advises that the cycle lane should continue through the junction to the left of the right-turn lane; however, this creates conflict where motor vehicles wish to enter the right lane, as they must cross the cycle lane at a bad angle.[54]

Under Dutch engineering principles, cyclists are instead kept to the right of the junction, with protected kerbs. This improves safety by putting cyclists into the eyeline of motor vehicles at the stop line, allowing cyclists a headstart over turning traffic. This design also allows cyclists to complete far-side turns without having to wait in the centre of the junction.[54] UK engineers have innovated on this design through the Cycle Optimised Protected Signals (CYCLOPS) junction, e.g. in Manchester. This places the cycle track around the edge of the signal junction and gives cyclists and pedestrians a single all-red phase, entirely separate from motor traffic and shortens pedestrian crossing times.[55]

Alternatively, cyclists can be considered pedestrians on approach to a junction, or where a cycle track crosses a road and combined pedestrian-cyclist traffic lights (known as Toucan crossings in the UK) can be provided.[56]

Public transport signals

[

edit

]

Traffic lights for public transport often use signals that are distinct from those for private traffic. They can be letters, arrows or bars of white or (an LED 100-watt typical) coloured light.

Transit signals in North America

[

edit

]

MUTCD specifies a standard vertically oriented signal with either two or three lenses, displaying white lines on a black background.[57]:&#;Fig.8C-3&#;

Some systems use the letter B for buses and T for trams. The METRO light rail system in Minneapolis, Minnesota, the Valley Metro Rail in Phoenix, Arizona, and the RTA Streetcar System in New Orleans use a simplified variant of the Belgian/French system in the respective city's central business district where only the "go" and "stop" configurations are used. A third signal equal to amber is accomplished by flashing the "go" signal.

Public transport signals in Europe

[

edit

]

In some European countries and Russia, dedicated traffic signals for public transport (tram, as well any that is using a dedicated lane) have four white lights that form the letter T.[citation needed] If the three top lamps are lit, this means "stop". If the bottom lamp and some lamps on the top row are lit, this means permission to go in a direction shown. In the case of a tram signal, if there are no tram junctions or turns at an intersection, a simpler system of one amber signal in the form of the letter T is used instead; the tram must proceed only when the signal is lit.

In North European countries, the tram signals feature white lights of different forms: "S" for "stop", "&#;" for "caution" and arrows to permit passage in a given direction.[58] In Sweden, All signals use white lighting and special symbols ("S", "&#;" and an arrow) to distinguish them from regular signals.

The Netherlands uses a distinctive "negenoog" (nine-eyed) design shown on the top row of the diagram;[59] bottom row signals are used in Belgium, Luxembourg, France, and Germany. The signals mean (from left to right): "go straight ahead", "go left", "go right", "go in any direction" (like the "green" of a normal traffic light), "stop, unless the emergency brake is needed" (equal to "amber"), and "stop" (equal to "red").

Public transport signals in the Asia-Pacific region

[

edit

]

In Japan, tram signals are under the regular vehicle signal; however, the colour of the signal intended for trams is orange. The small light at the top tells the driver when the vehicle's transponder signal is received by the traffic light. In Hong Kong, an amber T-signal is used for trams, in place of the green signal. In addition, at any tramway junction, another set of signals is available to indicate the direction of the tracks. In Australia and New Zealand, a white "B" or "T" sometimes replaces the green light indicating that buses or trams (respectively) have right of way.

Preemption and priority

[

edit

]

Some regions have signals that are interruptible, giving priority to special traffic, usually emergency vehicles such as firefighting apparatus, ambulances, and police cars.[60][61] Most of the systems operate with small transmitters that send radio waves, infrared signals, or strobe light signals that are received by a sensor on or near the traffic lights. Some systems use audio detection, where a certain type of siren must be used and detected by a receiver on the traffic light structure.

Upon activation, the normal traffic light cycle is suspended and replaced by the "preemption sequence": the traffic lights to all approaches to the intersection are switched to "red" with the exception of the light for the vehicle that has triggered the preemption sequence. Sometimes, an additional signal light is placed nearby to indicate to the preempting vehicle that the preempting sequence has been activated and to warn other motorists of the approach of an emergency vehicle. The normal traffic light cycle resumes after the sensor has been passed by the vehicle that triggered the preemption.

In lieu of preemptive mechanisms, in most jurisdictions, emergency vehicles are not required to respect traffic lights. However, emergency vehicles must slow down, proceed cautiously and activate their emergency lights to alert oncoming drivers to the preemption when crossing an intersection against the light.[62][63]

Unlike preemption, which immediately interrupts a signal's normal operation to serve the preempting vehicle and is usually reserved for emergency use, "priority" is a set of strategies intended to reduce delay for specific vehicles, especially mass transit vehicles such as buses. A variety of strategies exist to give priority to transit but they all generally work by detecting approaching transit vehicles and making small adjustments to the signal timing. These adjustments are designed to either decrease the likelihood that the transit vehicle will arrive during a red interval or decrease the length of the red interval for those vehicles that are stopped. Priority does not guarantee that transit vehicles always get a green light the instant they arrive as preemption does.

Operation

[

edit

]

A staging diagram for a typical signalised T-junction

A variety of different control systems are used to operate signal cycles smoothly, ranging from simple clockwork mechanisms to sophisticated computerised control systems. Computerised systems are normally actuated, i.e. controlled by loop detectors or other sensors on junction approaches. Area-wide coordination can allow green wave systems to be set up for vehicles or cycle tracks.[64] Smart traffic light systems combine traditional actuation, a wider array of sensors and artificial intellegence to further improve performance of signal systems.[65] A traffic signal junction or crossing is typically controlled by a controller mounted inside a cabinet nearby.[66]

"Phases" (or "signal groups" in Australia and New Zealand) are indications show simultaneously, e.g. multiple green lights which control the same traffic approach. A "movement" is any path through the junction which vehicles or pedestrians are permitted to take, which is "conflicting" if these paths cross one another. A stage (or "phase" in ANZ) is a group of non-conflicting phases which move at the same time. The stages are collectively known as a "cycle".[67] The time between two conflicting green phases is called an "intergreen period", which is set at an appropriate length for the junction to safely clear, especially for turning traffic which may be waiting in the centre of the junction. This often results in an all red stage, when all approaches are shown a red light and no vehicle can proceed. This all red is sometimes extended to allow a pedestrian scramble, where pedestrians can cross the empty junction in any direction all at once.[68] Some signals have no "all red" phase: the light turns green for cross traffic the instant the other light turns red.[c]

Many traffic light installations are fitted with vehicle actuation, i.e. detection, to improve the flexibility of traffic systems to respond to varying traffic flows. Detectors come in the form of digital sensors fitted to the signal heads or induction loops within the road surface. Induction loops are beneficial due to their smaller chance of breakdown, but their simplicity can limit their ability to handle some situations, particularly involving lighter vehicles such as motorcycles or pedal cycles.[69] This situation most often occurs at times of day when other traffic is sparse as well as when the small vehicle is coming from a direction that does not have a high volume of traffic.[70]

Timing

[

edit

]

Traffic light with time in Tehran, Iran

The timing of the intergreen is usually based on the size of the intersection, which can range from two to five seconds.[citation needed] Modelling programs include the ability to calculate intergreen times automatically. Intergreen periods are determined by calculating the path distance for every conflict point in the junction, which is the distance travelled to the conflict point by the movement losing right of way minus the distance travelled to the same conflict point by the movement gaining right of way using the possible conflict points (including with pedestrians) and calculating both the time it would take the last vehicle to clear the furthest collision point and the first vehicle from the next stage to arrive at the conflict point. At actuated junctions, integreens can be varied to account for traffic conditions.[19]

Engineers also need to set the amber timings (and red-amber, where appropriate), which is normally standardised by a traffic authority. For example, in the UK, the amber time is fixed nationally at three seconds and the red-amber time at two seconds, which results in a minimum intergreen time of five seconds (plus any all-red time).[19] The US also uses a minimum of three seconds, but local traffic authorities can make timings longer, especially on wider, suburban roads. This variation has resulted in controversy when municipalities with shorter amber times use red light cameras.[71] Where pedestrian signals are used, the timing of the "inivitation to cross" &#; the period where a steady walk signal shows &#; and clearance periods &#; time when the walk signal flashes or no signal is shown &#; need to be calculated. This is normally set against a design speed, e.g. 1.2 m/s (3.9 ft/s). Similarly, these can be made extendable using sensors, allowing slower-moving pedestrians more time to cross the street.[19]

Design guidance

[

edit

]

National or sub-national highway authorities often issue guidance documents on the specification of traffic signals and design of signalised intersections according to national or local regulations. For example, in the United States the Federal Highway Administration issues the Manual on Uniform Traffic Control Devices and the Signalized Intersections Information Guide, which is a synthesis of best practices and treatments to help practitioners make informed decisions.[72]

Variable lane control

[

edit

]

An LED 50-watt typical lane control signal head Lane control signals installed on the Old Champlain Bridge in Montréal, Canada

Variable lane control is a form of intelligent transportation systems which involve the use of lane-use control signals, typically on a gantry above a carriageway. These lights are used in tidal flow systems to allow or forbid traffic to use one or more of the available lanes by the use of green lights or arrows (to permit) or by red lights or crosses (to prohibit).[73] Variable lane control may be in use at toll plazas to indicate open or closed booths; during heavy traffic to facilitate merging traffic from a slip road.[73]

In the US, most notably the Southeastern, there often is a "continuous-flow" lane. This lane is protected by a single, constant-green arrow pointing down at the lane(s) permitting the continuous flow of traffic, without regard to the condition of signals for other lanes or cross streets. Continuous lanes are restricted in that vehicles turning from a side street may not cross over the double white line to enter the continuous lane, and no lane changes are permitted to the continuous lane from an adjacent lane or from the continuous lane to an adjacent lane until the double white line has been passed. Some continuous lanes are protected by a raised curb located between the continuous lane and a normal traffic lane, with white and/or amber reflective paint or tape, prohibiting turning or adjacent traffic from entering the lane.[citation needed]

Continuous-flow traffic lanes are found only at "T" intersections where there is no side street or driveway entrance on the right side of the main thoroughfare; additionally, no pedestrians are permitted to cross the main thoroughfare at intersections with a continuous-flow lane, although crossing at the side street may be permitted. Intersections with continuous-flow lanes will be posted with a white regulatory sign approximately 500 ft (150 m) before the intersection with the phrase, "right lane continuous traffic," or other, similar, wording. If the arrow is extinguished for any reason, whether by malfunction or design, traffic through the continuous lane will revert to the normal traffic pattern for adjacent lanes, except that turning or moving into or out of the restricted lane is still prohibited.[citation needed]

Waterways and railways

[

edit

]

The three-aspect standard is also used at locks on the Upper Mississippi River. Red means that another vessel is passing through. Amber means that the lock chamber is being emptied or filled to match the level of the approaching vessel. After the gate opens, green means that the vessel may enter.

Railroad signals, for stopping trains in their own right of way, generally use the opposite positioning of the colours; that is, for signals above the driver's eyeline, green on top and red below is the standard placement of the signal colours on railroad tracks. There are three reasons for this variation: there is no risk that railway signals will be masked by a tall vehicle between the driver and the signal; train speeds in fog are much higher than for road vehicles, so it is important that the most restrictive signal is closest to the driver's eyeline; and with railway signals often in exposed rural locations, there is a risk of any signal other than the bottom one being masked by snow building up on the hood of the signal below.

Rules

[

edit

]

California attempts to discourage red light running by posting the minimum fine.

Traffic lights control flows of traffic using social norms and legal rules. In most jurisdictions, it is against the law to disobey traffic signals and the police, or devices such as red light cameras, can issue fines or other penalties &#; and in some cases prosecute &#; drivers who break those laws.[74] US-based studies have found that the majority of drivers think that it is dangerous to run a red light at speed and the most common reason for red light running include inattentive driving, following an oversized vehicle or during inclement weather.[75][76]

The rules governing traffic light junctions for vehicles differ by jurisdiction. For example, it is common in North America that drivers can turn kerb-to-kerb (i.e. turning right at most junctions), even when a red light shows.[77][78] On the other hand, this turn on red rule is uncommon in Europe, unless an arrow signal or traffic sign specifically permits it.[79][80][81][82]

Design

[

edit

]

Bulbs

[

edit

]

Conventional traffic signal lighting, still common in some areas, uses a standard light bulb. The light then bounces off a mirrored glass or polished aluminium reflector bowl, and out through a polycarbonate plastic or glass signal lens. In some signals, these lenses were cut to include a specific refracting pattern. Traditionally, incandescent and halogen bulbs were used. Because of the low efficiency of light output and a single point of failure (filament burnout), some traffic authorities are choosing to retrofit traffic signals with LED arrays that consume less power, have increased light output, and last significantly longer.[citation needed] Moreover, in the event of an individual LED failure, the aspect will still operate albeit with a reduced light output. The light pattern of an LED array can be comparable to the pattern of an incandescent or halogen bulb fitted with a prismatic lens.

The low energy consumption of LED lights can pose a driving risk in some areas during winter. Unlike incandescent and halogen bulbs, which generally get hot enough to melt away any snow that may settle on individual lights, LED displays &#; using only a fraction of the energy &#; remain too cool for this to happen.[83][84] As a response to the safety concerns, a heating element on the lens was developed.[85][86]

Programmable visibility signals

[

edit

]

top) and from the signal's intended viewing area (bottom).

From off-axis, these signals appear to be "off" or invisible to adjacent lanes of traffic during the daytime. Only a faint glow can be seen when viewed at night.

Traffic signals installed in Shelton, Washington , seen off-axis from the intended viewing area () and from the signal's intended viewing area ().From off-axis, these signals appear to be "off" or invisible to adjacent lanes of traffic during the daytime. Only a faint glow can be seen when viewed at night.

Signals such as the 3M High Visibility Signal utilize light-diffusing optics and a Fresnel lens to create the signal indication. The light from a 150 W PAR46 sealed-beam lamp in these "programmable visibility" signals passes through a set of two glass lenses at the back of the signal. The first lens, a frosted glass diffusing lens, diffuses the light into a uniform ball of light around five inches in diameter. The light then passes through a nearly identical lens known as an optical limiter (3M's definition of the lens itself), also known as a "programming lens", also five inches in diameter.[citation needed]

Using a special aluminium foil-based adhesive tape, these signals are "masked" or programmed by the programming lens so that only certain lanes of traffic will view the indication. At the front of these programmable visibility signals is a 12" Fresnel lens, each lens tinted to meet United States Institute of Transportation Engineers (ITE) chromaticity and luminance standards. The Fresnel lens collimates the light output created by the lamp and creates a uniform display of light for the lane in which it is intended.

In addition to being positioned and mounted for desired visibility for their respective traffic, some traffic lights are also aimed, louvered, or shaded to minimize misinterpretation from other lanes. For example, a Fresnel lens on an adjacent through-lane signal may be aimed to prevent left-turning traffic from anticipating its own green arrow. Intelight Inc. manufactures a programmable traffic signal that uses a software-controlled LED array and electronics to steer the light beam toward the desired approach.[87] The signal is programmed unlike the 3M and McCain models. It requires a connection to a laptop or smartphone with the manufacturer's software installed. Connections can be made directly with a direct-serial interface kit, or wirelessly with a radio kit over WIFI to the signal. In addition to aiming, Fresnel lenses, and louvers, visors and back panels are also useful in areas where sunlight would diminish the contrast and visibility of a signal face. Typical applications for these signals were skewed intersections, specific multi-lane control, left-turn pocket signals, or other areas where complex traffic situations existed.

An animated GIF shows a traffic light in 3 reverted phases: red, yellow, then green

Size

[

edit

]

In the United States, traffic lights are currently designed with lights approximately 12 inches (300 mm) in diameter. Previously the standard had been 8 inches (200 mm); however, those are slowly being phased out in favour of the larger and more visible 12 inch lights. Variations used have also included a hybrid design, which had one or more 12 inch lights along with one or more lights of 8 inches (200 mm) on the same light.

In the United Kingdom, 12-inch lights were implemented only with Mellor Design Signal heads designed by David Mellor. These were designed for symbolic optics to compensate for the light loss caused by the symbol. However, following a study sponsored by the UK Highways Agency and completed by Aston University, Birmingham, UK, an enhanced optical design was introduced in the mid-s. Criticism[by whom?] of sunlight washout (cannot see the illuminated signal due to sunlight falling on it), and sun-phantom (signal appearing to be illuminated even when not due to sunlight reflecting from the parabolic mirror at low sun angles), led to the design of a signal that used lenslets to focus light from a traditional incandescent bulb through apertures in a matt black front mask. This cured both problems in an easily manufactured solution. This design proved successful and was taken into production by a number of traffic signal manufacturers through the engineering designs of Dr. Mark Aston, working firstly at the SIRA Ltd in Kent, and latterly as an independent optical designer.[citation needed]

The manufacturers took a licence for the generic design from the Highways Agency, with Dr. Aston engineering a unique solution for each manufacturer. Producing both bulb and LED versions of the signal aspects, these signals are still the most common type of traffic light on UK roads. With the invention of anti-phantom, highly visible Aston lenses, lights of 8 inches (200 mm) could be designed to give the same output as plain lenses, so a larger surface area was unnecessary. Consequently, lights of 12 inches (300 mm) are no longer approved for use in the UK and all lights installed on new installations have to be 200 mm (8 in) in accordance with TSRGD (Traffic Signs Regulations and General Directions). Exemptions are made for temporary or replacement signals.[citation needed]

Mounting and placement

[

edit

]

The MUTCD identifies five types of traffic light mounts. On pedestals, signal heads are mounted on a single pole (this is the normal installation method for the UK).[89][19] On mast arms, signal heads are mounted on a rigid arm over the road protuding from the pole. On strained poles, signals are suspended over a roadway on a wire, attached to poles at opposite kerbs. This is the most common installation method in the United States. Unipoles are similar to strain poles, but a single structure over the road, rather than two poles linked with wire. Finally, signals can be attached to existing structures such as an overpass.[89] Dummy lights are traffic signs located in the centre of a junction, which operate on a fixed cycle. These have generally been decommissioned due to safety concerns; however, a number remain due to historic value.[90]

Signals can either be placed nearside &#; between the stop line and the kerbline of the intersecting road &#; or farside &#; on the opposite side of the junction. In European countries, signals are often placed on the nearside.[91] In the UK, at least two signal heads are required (known as the primary and secondary heads), one of which is normally nearside and the other of which could be nearside or farside.[19] In the US, signals are normally located farside, though in some states, nearside signals are also used. Nearside signals can be beneficial to road safety, as drivers have more time to see a red light and are less likely to encroach on pedestrian crossings.[91]

Effects

[

edit

]

Drivers spend on average around 2% of journey time passing through signalised junctions.[92] Traffic lights can increase the traffic capacity at intersections and reduce delay for side road traffic, but can also result in increased delay for main road traffic.[93] Hans Monderman, the innovative Dutch traffic engineer, and pioneer of shared space schemes, was sceptical of their role, and is quoted as having said of them: "We only want traffic lights where they are useful and I haven't found anywhere where they are useful yet."[94]

A World Economic Forum study found that signalised junctions are linked to higher rates of localised air pollution. Drivers accelerate and stop frequently at lights and as such peak particle concentration can be around 29 times higher than during free-flow conditions. The WEF recommends that traffic authorities synchronise traffic signals, consider alternative traffic management systems and consider placing traffic lights away from residential areas, schools, and hospitals.[92]

The separation of conflicting streams of traffic in time can reduce the chances of right-angle collisions by turning traffic and cross traffic, but they can increase the frequency of rear-end crashes by up to 50%.[95] Since right-angled and turn-against-traffic collisions are more likely to result in injuries, this is often an acceptable trade-off. They can also adversely affect the safety of bicycle and pedestrian traffic. Between and , the city of Philadelphia, Pennsylvania, removed signals at 199 intersections that were not warranted. On average, the intersections had 24% fewer crashes after the unwarranted signals were removed.[95] The traffic lights had been erected in the s because of since-resolved protests over traffic. By , over 800 traffic lights had been removed at 426 intersections, and the number of crashes at these intersections dropped by 60%.[96]

Justification

[

edit

]

Criteria have been developed to help ensure that new traffic lights are installed only where they will do more good than harm and to justify the removal of existing traffic lights where they are not warranted. They are most often placed on arterial roads at intersections with either another arterial road or a collector road, or on an expressway where an interchange is not warranted. In some situations, traffic signals can also be found on collector roads in busy settings.

The International Municipal Signal Association provides input as to standards concerning traffic signals and control devices. One example is the input the association provided for the Manual on Uniform Traffic Control Devices (MUTCD).[97] The MUTCD is issued by the Federal Highway Administration (FHWA) of the United States Department of Transportation (USDOT).[98]

In the United States, the criteria for installation of a traffic control signal are prescribed by the Manual on Uniform Traffic Control Devices (MUTCD), which defines the criteria in nine warrants:[99]

  • Eight-hour vehicular volume. Traffic volume must exceed prescribed minima for eight hours of an average weekday.
  • Four-hour vehicular volume. Traffic volume must exceed prescribed minima for four hours of an average weekday.
  • Peak hour volume or delay. This is applied only in unusual cases, such as office parks, industrial complexes, and park and ride lots that attract or discharge large numbers of vehicles in a short time, and for a minimum of one hour of an average weekday. The side road traffic suffers undue delays when entering or crossing the major street.
  • Pedestrian volume. If the traffic volume on a major street is so heavy that pedestrians experience excessive delays in attempting to cross it.
  • School crossing. If the traffic density at school crossing times exceeds one per minute which is considered to provide too few gaps in the traffic for children to safely cross the street.
  • Coordinated signal system. For places where adjacent traffic control signals do not keep traffic grouped together efficiently.
  • Crash experience. The volumes in the eight- and four-hour warrants may be reduced if five or more right-angle and cross traffic turn collisions have happened at the intersection in a twelve-month period.
  • Roadway network. Installing a traffic control signal at some intersections might be justified to encourage concentration and organization of traffic flow on a roadway network.
  • Intersection near a grade crossing. A traffic control signal is often justified at an intersection near a railroad crossing, in order to provide a preemption sequence to allow traffic queued up on the tracks an opportunity to clear the tracks before the train arrives.

In the US, an intersection is usually required to meet one or more of these warrants before a signal is installed. However, meeting one or more warrants does not require the installation of a traffic signal, it only suggests that they may be suitable. It could be that a roundabout would work better. There may be other unconsidered conditions that lead traffic engineers to conclude that a signal is undesirable. For example, it may be decided not to install a signal at an intersection if traffic stopped by it will back up and block another, more heavily trafficked intersection. Also, if a signal meets only the peak hour warrant, the advantages during that time may not outweigh the disadvantages during the rest of the day.

In other contexts

[

edit

]

The symbolism of a traffic light (and the meanings of the three primary colours used in traffic lights) are frequently found in many other contexts. Since they are often used as single spots of colour without the context of vertical position, they are typically not comprehensible to up to one in ten males who are colour blind.[citation needed]

Traffic lights have also been used in computer software, such as the macOS user interface, and in pieces of artwork, particularly Traffic Light Tree in London, UK.

Racing

[

edit

]

Automobile racing circuits can also use standard traffic signals to indicate to racing car drivers the status of racing. On an oval track, four sets may be used, two facing a straight-away and two facing the middle of the 180-degree turn between straight-away. Green would indicate racing is underway, while amber would indicate to slow or while following a pace car; red would indicate to stop, probably for emergency reasons.

Scuderia Ferrari, a Formula One racing team, formerly used a traffic light system during their pit stops to signal to their drivers when to leave the pits.[citation needed] The red light was on when the tires were being changed and fuel was being added, amber was on when the tires were changed, and green was on when all work was completed. The system is (usually) completely automatic. However, the system was withdrawn after the Singapore Grand Prix, due to the fact that it heavily delayed Felipe Massa during the race, when he was in the lead. Usually, the system was automatic, but heavy traffic in the pit lane forced the team to operate it manually. A mechanic accidentally pressed the green light button when the fuel hose was still attached to the car, causing Massa to drive off, towing the fuel hose along. Additionally, Massa drove into the path of Adrian Sutil, earning him a penalty. He finally stopped at the end of the pit lane, forcing Ferrari's mechanics to sprint down the whole of the pit lane to remove the hose. As a result of this, and the penalty he also incurred, Massa finished 13th. Ferrari decided to use a traditional "lollipop" for the remainder of the season.

Another type of traffic light that is used in racing is the Christmas Tree, which is used in drag racing. The Christmas Tree has six lights: a blue staging light, three amber lights, a green light, and a red light. The blue staging light is divided into two parts: Pre-stage and stage. Sometimes, there are two sets of bulbs on top of each other to represent them. Once a driver is staged at the starting line, then the starter will activate the light to commence racing, which can be done in two ways. If a Pro tree is used, then the three amber lights will flash at the same time. For the Sportsman tree, the amber light will flash from top to bottom. When the green light comes up, the race officially begins but if a driver crosses the line before that happens, then a red light will come up and that will be a foul. [citation needed]

As a rating mechanism

[

edit

]

The colours red, amber, and green are often used as a simple-to-understand rating system for products and processes. It may be extended by analogy to provide a greater range of intermediate colours, with red and green at the extremes.[100]

In Unicode

[

edit

]

In Unicode, the symbol for U+1F6A5 &#; HORIZONTAL TRAFFIC LIGHT is HORIZONTAL TRAFFIC LIGHT and U+1F6A6 &#; VERTICAL TRAFFIC LIGHT is VERTICAL TRAFFIC LIGHT.

See also

[

edit

]

Notes

[

edit

]

  1. ^[

    clarification needed

    ]

    Not completely correct: a variable speed sign is not solely used for the purpose of slowing the speed of motorists approaching an intersection. They are also used on freeways where the maximum safe speed is dependent on the conditions of the roadway (i.e. weather, falling rocks, risk of wildlife, etc.), such as in British Columbia, Canada.

  2. ^

    The Barnes Dance is named after an American traffic engineer, Henry A. Barnes . Barnes did not claim to have invented the system but was a strong advocate of it, having observed the difficulties his daughter faced crossing the road to get to school.

  3. ^[

    citation needed

    ]

    These are typically older signals. There are many examples in Houston, Texas, of this. Suspended lights constructed so that a single source simultaneously illuminates all four directions always have this characteristic: Red (in two directions) and green (in the two cross directions) with Red-Yellow-Green sequence on two sides and Green-Yellow-Red sequence on the cross sides

References

[

edit

]

Citations

[

edit

]

If you want to learn more, please visit our website types of traffic lights.