0.95 inch OLED Display, OLED 0.95

Pin Number Symbol I/O Function 1. N.C. (GND) - Reserved Pin(Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground. 2. VCC P Power Supply for OLED Panel
This is the most positive voltage supply pin of the chip.It must be supplied externally. 3. VSS P Ground of Logic Circuit
This is a ground pin. It also acts as a reference for the logic pins. It must be connected to external ground. 4. VDD P Power Supply for Logic Circuit
This is a voltage supply pin. It must be connected to external source. 5. VDDIO P Power supply for interface logic level.
It should be match with MCU interface voltage level. VDDIO must always be equal or lower than VDD. 6. BS1
BS2 I Communicating Protocol Select
These pins are MCU interface selection input. See the following table:   68XX-parallel 80XX-parallel Serial I2C BS1 0 1 0 1 BS2 1 1 0 0 7. 8. CS# I Chip Select
This pin is the chip select input. The chip is enabled for MCU communication only when CS# is pulled low. 9. RES# I Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed. 10. D/C# I Data/ Command Control
This pin is Data/Command control pin. When the pin is pulled high, the input at D7~D0 is treated as display data. When the pin is pulled low, the input at D7~D0 will be transferred to the command register. For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams.
When the pin is pulled high and serial interface mode is selected, the data at SDIN is treated as data. When it is pulled low, the data at SDIN will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. 11. R/W# I Read/ Write Selector Write
This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to &#;High&#; for read mode and pull it to &#;Low&#; for write mode.
When 80XXinterface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. 12. E/RD# I Read/Write Enable or Read
This pin is MCU interface input. When interfacing to a68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low.
When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. 13. D0~D7 I/O Host Data In put/ Output Bus
These pins are 8-bit bi-directional data bus to be connected to the microprocessor&#;s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2Cmode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL. 14. 15. 16. 17. 18. 19. 20. 21. IREF I Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 10μA. 22. VCOMH O Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS. 23. VCC P Power Supply for OLED Panel
This is the most positive voltage supply pin of the chip.It must be supplied externally. 24. VLSS P Ground of Analog Circuit
This is an analog ground pin. It should be connected to VSS externally. 25. N.C. (GND) - Reserved Pin(Supporting Pin)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

• 0.95 inch OLED Screen Small AMOLED 120×240 Video:

• Specifications:

Part Number

IF010TPS12-24C

Brand

IFANTEK

Diagonal Size

0.95&#;

Panel Type

AMOLED, OLED

Resolution

120(RGB)×240, 282PPI

Orientation

Portrait type

Display Area

10.8(W)×21.6(H) mm

Outline Size

12.8×27.35×0.75 (H×V×D) mm

Viewing Angle

80/80/80/80 (Min.)(CR&#;10)

Luminance

300 cd/m² (Typ.)

Color Gamut

16.7M

Contrast Ratio

: 1 (Typ.) (TM)

Interface

SPI, 24 pins

Driver IC

FT, CST816S (TP)

Operating Temperature

-20 ~ 70 °C

Application

Wearable, Portable Devices

Product Overview

The 0.95 inch OLED Screen Small AMOLED Panel 120×240 is an advanced display module that utilizes AMOLED (Active Matrix Organic Light-Emitting Diode) technology.

If you are looking for more details, kindly visit our website.

With its compact size and impressive high resolution of 120×240 pixels, this screen offers a high pixel density of 282 PPI, resulting in sharp and vibrant visuals. The display driver IC FT & touch screen driver IC CST816S, integrated into the screen and touch panel, enables seamless communication with the display through the SPI interface.

Applications of the 0.95 inch OLED Screen

• Wearable Devices

With the rise of wearable technology, the demand for small, power-efficient displays has soared. The 0.95 inch OLED screen fits perfectly into this category, providing an excellent visual experience for smartwatches, fitness trackers, and other wearable devices. Its low power consumption, high contrast ratio, and fast response time enhance the overall user experience.

You will get efficient and thoughtful service from ORIC Electronics.

• Medical Devices

In the field of medical technology, accuracy and reliability are of utmost importance. The 0.95 inch AMOLED screen&#;s vivid image quality, wide operating temperature range, and high luminance make it an excellent choice for medical devices such as patient monitors, diagnostic equipment, and portable medical devices.

• Portable Devices

The 0.95 inch OLED screen&#;s thin form factor, lightweight design, and excellent image quality make it an ideal choice for devices such as e-readers, handheld gaming consoles, and portable media players.

If you are looking for more details, kindly visit 0 95 inch amoled display.